1. Please charge the receiver before the first using, then pressing the key
   ENT 5 seconds to enter into standby mode after full charging (clock
   display time). Please turn off the receiver before charging. When the
   charging indicator light becomes green color, you can use it.
2. Standby mode, OLED screen display will turn off automatically after 5 seconds. OLED screen display will light by pressing keys or the pagers calling.
3. Please initialize the receiver before the first registration.
4. When the function setting cannot be use, please reference to 10 ‘password setting’ to confirm whether the pager is encryption (default set is not encryption). After decryption, all function can be set

1. Power on: Power off mode, press and hold key [ENT] for 5 seconds,
   power is on.
2. Power off: Power on mode, press and hold key [ENT] for 5 seconds, power is off.

1. Standby mode, press and hold [FUN] till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F05’.
3. Press and hold [FUN] till 000 appears, and press key [ENT] 3 seconds
   to start the initialization. The LED screen shows “—“. When ‘000’
   appears again, the initialization is done.
4. Press and hold [FUN] till ‘F05’ appears.
5. Press and hold [ENT] till back to standby mode (time mode).The initialization is done.

1. Standby mode, press and hold key [FUN], until ‘F01’ shows on the
   screen.
2. Press and hold key [FUN] until the number ‘001’or ‘001-01’appears.
   There are two kinds of number format. (Refer to step 9 to change the
   format).
3. Press [ENT] to change the flashing number, press [FUN] to move the
   cursor (each position can set from 0-9 and A-Z).
4. Press and hold key [ENT] to delete the current number. (If this number
   is registered before, the number is flashing that means deletion is
   successful. Otherwise, the number will not flash that mean this number
   is not registered before.)
5. After getting the number you want, press down the call pager, the
   receiver vibrated with the registered number flashing on the screen,
   the registration is finished.
6. To register more than one pager, please repeat the 5) after the first
   one finished.
7. After finishing the all numbers, press and hold key [FUN] till ‘F01’
   shows on screen.
8. Press and hold [ENT] till back to standby mode. The register is done. the calling signal.

Note:

1. Can register 500 numbers at most.
2. During the registration, if the number does not flash or vibrate that
   means the number is not registered successfully. You can judge the
   problems according to the digits behind the calling number:
   1-Means this number is not registered, but this pager has been
   registered to another number.
   2-Means this number has been registered by other pager before.
   3-Means the pager and number are both registered successfully.
   4-Means the number capacity has got the limitation of 500.
   No digit means the receiver did not get the calling signal.

The calling number shows on the screen (The cycle interval time is two
seconds, the maximum is ten numbers.)

1. Press and hold [FUN] to delete all called numbers to back to standby
   mode. This way can delete all called numbers with only one key.
2. Short press [ENT] to delete the current calling number. This way can
   delete the current calling numbers with only one key.

1. Standby mode, press and hold key [FUN] 3 seconds till ‘F01’ appears.
2. Press key [ENT] to choose ‘F02’.
3. Press and hold [FUN] till a number ‘01-15’ appears. Press key [ENT] to
   choose the number you want. (‘01-15’ means 1-15 seconds of
   vibration prompt time, one digit means one second.)
4. Press and hold [FUN] till ‘F02’ appears again.
5. Press and hold [ENT] till back to standby mode, vibration time setting
   is done.

1. Standby mode, press and hold key [FUN] 3 seconds till ‘F01’ appears.
2. Press key [ENT] repeatedly to choose ‘F03’.
3. Press and hold [FUN], till a number between 00 and 99 appears. Press
   [ENT] to change the flashing number, press [FUN] to change the cursor
   position. The number 01-99 means the time is 01-99 seconds, 00
   means unlimited display.
4. Press and hold [FUN] till ‘F03’ appears.
5. Press and hold [ENT] till back to standby mode. The display time
   setting is done.

1. Standby mode, press and hold [FUN] 3 seconds till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F04’.
3. Press and hold [FUN] till the smallest registered number appears on
   screen.
4. Press [FUN] repeatedly to choose the number to be deleted, then
   press and hold [ENT] to delete it. And the next registered number will
   appear on the screen after the deleting.
5. Press and hold [FUN] till ‘F04’ appears.
   6. Press and hold [ENT] till back to standby mode. Deleting is done.

1. Standby mode, press and hold [FUN] 3 seconds till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F06’.
3. Press and hold [FUN] into the time mode, for example ‘08︰10
   16/05/25’ (hour, minute, year, month, day) appears.
4. Press [ENT] to set clock time and year, month, day and press [FUN] to
   choose hour, minute, year, month, day.
5. After time setting, press and hold [FUN] till ‘F06’ appears.
6. Press and hold [ENT] till back to standby mode. Time setting is done.
   Time will return to zero if the battery used out. It needs to reset after
   charging.

1. Standby mode, press and hold [FUN] till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F07’.
3. Press and hold [FUN] till ‘00’ or ‘01’ appears
   ‘00’ means the number display mode is XXX (the default number is
   ‘00’)
   ‘01’ means the number display mode is XXX-XX
   Press [ENT] to change the number between ‘00’ and ‘01’.
4. Press and hold [FUN] till ‘F07’ appears.
5.  Press and hold [ENT] to back to standby mode. Display mode setting is
   done.

1. Standby mode, press and hold [FUN] 3 seconds till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F08’.
3. Press and hold [FUN] till XXX appears on screen.
4. Press [ENT] to change the flashing number, press [FUN] to change the
   cursor position (the password is 181. Only when the number is 181, all
   functions can be set.
   Note:
   It is better to set the password after all functions have been set. (If the
   number is not 181, all functions can not be set.) In case that the
   products is not used normally by mistake changes of the information.
5. Press and hold [FUN] till ‘F08’ appears.
6. Press and hold [ENT] till back to standby mode. Password setting is
   done.

1. Standby mode, press and hold [FUN] 3 seconds till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F09’.
3. Press and hold [FUN] till ‘1 XX:XX’ or ‘2 XX:XX’ appears on the
   screen(1 and 2 are the sequence numbers of the alarm. XX:XX is hour
   and minute ).
4. Press [ENT] to set the sequence number of clock, hour and minute,
   press [FUN] to choose the position.
5. Press and hold [FUN] till ‘F09’ appears.
6. Press and hold [ENT] till back to standby mode. Alarm clock setting is
   done.

1. Standby mode, Press and hold [FUN] 3 seconds till ‘F01’ appears.
2. Press [ENT] repeatedly to choose ‘F10’.
3. Press and hold [FUN] till ‘1: ON/OFF’ or ‘2: ON/OFF’ appears on the
   screen. (1and 2 are the sequence numbers of alarm, ON-turn on, OFFturn off）
4. Press [ENT] to choose the alarm clock to ON or OFF, press [FUN] to
   choose the alarm clocks.
5. Press and hold [FUN] till ‘F10’ appears.
6. Press and hold [ENT] till back to standby mode. Alarm clock ON/OFF
   setting is done.
   Note:
   When the alarm clock is on:
   a) Alarm prompt mode is vibration
   b) Alarm prompt time is the same with the vibration time set in ‘F02’
   c) Alarming in standby mode or calling mode (called number is
   displaying on the screen), alarm mark is flashing.
   d) Press key [FUN] for one second to stop alarming

1. When the product does not use for a long time, it is better to charge
   every two months to avoid damaging the battery. Charge the receiver
   before showing the low battery. It can prolong the life of battery. The
   product may shut down automatically when battery is low.
2. Please use our original parts, especially the original battery and
   charger.
3. Only after quitting from the setting mode, all the functions can be back
   to working mode.
4. If you find any unusual problems, please consult our after-sale staff
   immediately. Do not dismantle the products by yourself to cause the
   unnecessary troubles

• Watch receiver 1 pc
• Recharger 1 pc
• User Manual 1 pc